After I didn't get the planned car for the conversion back, I'm ending the Mercedes W123 project.
If anyone is interested in the Nissan Leaf components (except battery) please let me know.
I also have a zombieverter with shunt

I also have lead batteries that I can connect to a 400V system for ...

Hallo,
ich werde mein Projekt das ich begonnen habe aufgeben und verkaufen !
Ich wollte einen Mecedes W124 umbauen mit Nissan Leaf Komponenten.
Leider ist der Wagen nie mehr zurück gekommen vom Lackierer in Serbien.
Nun hat mich die Lust verlassen für einen Umbau.

Ich hatte mir einen Leaf gen1 ...

i have checked all connections !

Do any of you have GEN1 working on the Zonmbie?

Just for your information:
I also had problems at the beginning that the PC can connect to the Zombie !

After that I used a USB - Wifi and now the connection works!

Digitus DN-7042-1 WLAN Stick USB 2.0 150 MBit/s

thanks for the tip

I have already seen the video

do you have a solution?

https://www.youtube.com/watch?v=vHrb0n2qNzM

these are my parameters

I cannot find an error
do you have the solution

danke
peter


parameter value
Vehicle Module
Inverter Leaf_Gen1
Vehicle None
Throttle
potmin 156 dig
potmax 840 dig
pot2min 305 dig
pot2max 2042 dig
regentravel 30 %
regenmax -30 ...

Hello,

I am very glad that the motor turns !!!

forwards everything is OK
only in reverse the engine turns to a constant speed and stays there until I switch to forward again

what could be the problem ?

Hello,

I am very glad that the motor turns !!!

forwards everything is OK
only in reverse the engine turns to a constant speed and stays there until I switch to forward again

what could be the problem ?

thanks for the video !

It has shown me many interesting things !

Hi Dämon
I have the same problem and can't get CAN signals to CAN2.


Hi Paul
I can take photos tomorrow of how I soldered the loose components onto the board.

then we can try to compare

thank you for the support !!

only short question

should on CAN2 from the VCU signals come only with 12V applied ?

So that I can control my CAN connection and be sure that the VCU is working properly!
Now there are no CAN signals!

Thank you

unfortunately I don't have an Arduino Due
only Nano

Have I understood this correctly?
This is a code that I run via an Arduino which then sets the correct parameters in the Shant ?
I will try it


One more question
If I apply voltage to the Zombie board, should CAN signals arrive at CAN2 ...

Thanks for the answer !
Where can I find the code ?
( code in the zombieverter project (ISA::initialize) )

unfortunately I have a problem with the shunt !

It is strangely set to 1000kbps ( should be 500 )

I then tried to set it to 500kbps according to the instructions.

now I cannot receive any ...

Hello
I need your help again
I have ordered the shunt and connected it

unfortunately I don't get any correct data displayed in the web interface

for example

udc 16777.18
udc2 -33554.4
udc3 -64225.25
idc -50311.62

If I connect an Arduino CAN shield with this code

https://openinverter.org/wiki ...

Thank you this has helped me a lot !!!

Please link it on the wiki page !!!


Thanks
Peter

hello,

I hope you can help me!

The first question :
what does the red flashing LED on the zombieverter board mean ?

I have a red one on the ESP and a red one on the board that are permanently lit and one on the board that is flashing.

2. i don't get any CAN data from the board
What settings do I ...

thank you for your message

hello
I have a simple question
how do the components that come loose in the kit are positioned?

they are not the same parts as in the video

there is no marking on the parts

does anyone have photos of the board



or a link where it is described

thanks
peter

Thank you for your professional answer !

If I connect the BMS and the charger with CAN, the system will work without the VCU?

as in this diagram :

https://activeautomation.co.nz/images/thumbs/0000631_blogimages.jpeg

I have another question:

I wanted to try powering the charger with 12V to read ...

Hi
I think this is better if it is here

it is about the zombieverter

please for a technical information

Thanks
Peter

Hello conversion friends,

I am Peter from Germany and a beginner in converting vehicles !
I will install a Leaf Gen1 in a Mercedes W123.
Both cars I already have and the Leaf components I have already removed
I have already ordered the ZombieVerter

I have a request to the specialists

Which of ...