Did you manage to get this working

we are in Stroud - GL60DE

Hi guys

I am looking for matching Mitsubishi rear motor and inverter.

Please let me know if any of you have something for sale or where I can look.

much blessings
james

Hi

I bought the Mitsubishi generator and front inverter from 2 different sources.
Does the generator and inverter have to be from the same vehicle?

If you take a look at the Software Update section of the Zombieverter wiki page https://openinverter.org/wiki/ZombieVerter_VCU you'll see a photo of the connections. The red wire is tapping into a 3.3V line to power on the VCU. The other three wires are labelled on the VCU and the ST-Link (clk ...

Thanks so much for your post - you have given me hope
1. Can you please send me pics of how you connect to the serial not using wifi
2. I need to know which plugs or converters to use from a laptop to the board
3. What program do you use to update?

i didn't manage to do that as yet and test it out. will do so and update you guys.

the auto refresh does not give the spot values

Question : I managed to get the board working again via the wifi. I now left it connected to the battery as it loses it's toggle category visibility if i disconnect. Is ...

There is no need to reset the board to upload but I find occasionly the wifi module needs resetting after. This is easy if working on the bench with the Wemos module as it has a reset button, otherwise power cycle the board. Are you using a board from Damien with the firmware pre-intstalled?


I ...

Have you mapped your throttle yet? You can select the pot values to graph, and click start graph, watch the plot change as you move the throttle. Set pot min and pot max to fit the values in the range your Thorttle pedal provides,

Also you must set up the type of throttle, single, single regen ...

do i have to reset the board to upload the software

as when i upload it goes though to 100%, says update done - however there is no change and still cannot see spot values

I changed UDC to 0 volts and now opmode says run

however throttle 2 error comes up when i click refresh

Hi Everyone

Great news - i tried uploading software onto zombieboard many many times and it did not want to work.

On Sunday i was showing someone how it didn't work and it did.

So now i got the spot values.

Next problem- when i do the op mode by switching T15 on and HV request on (Time code 01 ...

Sorry Adrian i forgot to reply to you - yes we using the Wemos one

Update - the activity led is not flashing at all

Thanks guys - will attempt to get a usb serial adaptor and try to work out how to do it

Will also try to isolate inverter and shunt and see what happens

Thanks again

we uploaded via UART
both ISA shunt and inverter were on CAN 2.
Is this correct?

1. We uploaded the stm32_vcu. bin file
2. It says upload complete but never has any percentage no matter how long we wait.
3. We are receiving burst of data from laptop to out of wifi module
4. No signal returned from CPU
5. Have checked all supply voltages are present (12v, 5v and 3,3volts)
6 ...

Yes you are right - i used SWD.

However i did use the UART update function. I downloaded the stmvcu_32.bin file.

When i uploaded the file - it said update completed.

It's still not showing spot values.

Hi

I initially was getting the spot values.

We were getting some strange voltage values from our shunt

We realised we connected shunt to 5volt supply.

We then changed the supply to 12volts.

When we switched everything on again we got no spot values.

I tried reloading the sim32_vcu.bin. Its ...

Hi guys

Can someone please help me with the wiring for the inverter to connect to the ZombieVerter.

I need the 12 volts, ground, can high and can low wire colours.

Please see screenshot of Damien video however i cannot make out the wiring.

Thanks

Hi guys

I am using the front generator motor with the front inverter for our ev setup.

Can someone please tell me what the connections on the attached pic are.

I need to know where the dv voltage goes and which 3 terminals to connect to the motor.

Thanks

Hi Everyone

Does anyone know what the 6 wires on the Mitsubishi Outlander accelerator pedal do?

I need to connect to ZombieVerter.

Thanks

Hi guys

I have the gigavac gv242mab contractors and resistors.

What do the red, black, white and blue wires do?

Does anyone have a precharge and HV circuit we can follow?

Thanks

Hello Everyone

Blessed New Year to you all.

Has anyone got a Mitsubishi Outlander charger for sale?

Thanks
james

Hi All

I am looking for
1. IVT-1K-U3-I-CAN2-12
2. Gigavac GV242MAB contactor with built in economisers
3. Panasonic AEV52012 Relay

Thanks
james

Hello Everyone

I am looking for ff
1. IVT-1K-U3-I-CAN2-12
2. Gigavac GV242MAB contactor with built in economisers
3. Panasonic AEV52012 Relay

Thanks
james