Hello everyone,

I also use the BMS provided by Charly and it works very well too! Thank you again for your work Charly!

now to my problem:
I have the following setup:
Daisychain BMS, Zombie VCU, Tesla SDU with the IO board and BMW LiM.

Unfortunately, I haven't managed to charge the batteries with ...

Hi Folks,

I have the following setup: Zombie VCU, Tesla SDU OI board, BMW LiM, Volvo batteries with this BMS: https://openinverter.org/forum/viewtopic.php?t=2123
I do not want to use an AC onboard charger because for home charging I have a CCS2 DC Charger and on the road there are enough fast ...

Hi there

Thank you for your reply.

I would like to use these batterys in my shed as a power source for my ham radios.
But don't know how to arrange these to a power bank as they need to be on a bms .
Each battery have a board and I have all the links
But don't know on what program or how to ...

Hi there

just saw your post on the battery's and the BMS system . BMS board with 16s li-ion battery BQ76PL455A

i have acquired 15 of this batteries with this boards on i do also have teh manage ment boxes but dont have a clu how to make this work for me ,could you please help me on how to ...

Hello,

quick update and hopefully someone has an idea what to do...

I now only have a cable of about 20 cm. from the battery module to the master BMS board. Since I have two strings in parallel, two mast boards were now used and communication with the Zombie VCU happens via can bus.

Charlie ...

Zombie uses some fixed CAN mapping for OI (it's probably documented somewhere...) and you have to add the appropriate mapping on the inverter side. That is until inverter firmware 5.27.R
From 5.32.R the inverter has a fixed mapping, not sure if Zombie is adjusted to that yet?


Thank you for your ...

I never went down the Zombieverter route. Just stuck with the OI board in the SDU and using ESP32s for various VCU functions. Not got everything working together yet and I just killed my SDU so will be putting things on hold until I get another SDU.

I think you are correct about needing to map ...

Hello,

I have a Tesla SDU with the Openinverter board installed but have been following development of the Zombieverter with great interest. Would it be possible to have the Openinverter board control the SDU as normal but also have a Zombieverter onboard to control everything else such as ...

If anyone is looking for the connector:

JST 04CPT-B1-2A

https://at.rs-online.com/web/p/kfz-stec ... er/1238228

Update:

After a Long Night with several tries, I can tell you…THE MASTER IS ALIVE!

As conclusion I can tell you what I did, that the master is running:
I compiled the code once more, now with ninja. I think there was a fault in the uf2 file.
Changed all cables to new one.
120 ohm resistor at the ...

Hi Folks!

I have ordered the master boards, and they have arrived. I uploaded the UF2 file, and behold, I get a reaction... unfortunately, it's the wrong one... countless CRC errors. So, thinking that I might have made a mistake in the configuration of the UF2 file due to my lack of coding skills ...

Hello,

I just ordered the boards…the first time for me doing this🤪 I hope I did it correct.

Now my question is, how to measure the SoC. can I do this with the Raspberry Pico I use on this board or do I need another board, which takes the Voltage via CAN from this board.

Other option would be to ...

Ahhh…ok…

I think you already told me, that I can purchase the hardware from you. Correct?

If yes, please send me via PM the price and where I have to send the money…Is it also possible to get a Display for reading the SOC, Temperature and momentary current?

Thank you and best regards

Volkmar

Hi Catphish,

thank you for your replay...

Now the things have changed...because my 2 Motenergy ME1616 motors were too weak I decided to change them into one Model S SDU. This was a lot of work, but now it is done and I have only a few things left to do...like reversing the oil pump and a few other ...

Sorry I didn't reply sooner. Can you confirm exactly what batteries you have? Do you have a photo?


Now I have to say sorry for my late reply! :?

I have bought the complete battery pack of a Volvo XC 90 Plugin Hybrid from 2017.

I will send you detailed picture tomorrow, when I am back in my ...

Hi,

I am completly new in this forum and I am afraid, I am a coding fool :-(

I have purchased for my homemade electric vehicle a complete Volvo XC90 hybrid battery and I have a SimpBMS for Tesla modules at home. Do you think there is a possibility to use the Simp BMS with the Volvo Batteries ...