Sold

Now anyone could say how the rpm/V is? I really need 600V for reach the 50kW?

3900€!

Hello,
i would try another Motor,so Ive selling my Tesla SDU including drive shafts, power cables and low voltage wiring harness.
The EVBMW Controller is build in, and the Oilpump is modified to spin the engine reverse (So the Gearbox is "follow", like in the most cars).

Price: 4500€ VB (Location ...

No more Boards for the Tesla S Units? Ok, thats hard. Luckely i had ordered it soon enough.

@all: Anyone realize an ESP with the Tesla Units (lower the Output Power when ESP gets active)? My Smart Roadster has an ESP Module with "Trust+" that could communicate with CAN.

And how i could realize a ...

Ok, thanks. So it should be ok to usw 100 cells in a row instead of 96

Does anyone know what about the maximum supply voltage?

Ok, sounds easy. Only connect one Phase and go for 240v Single Phase and connect three for 400v 3 Phase. Max current are the same per Phase.

PS. Could i switch the Max amp without open the Controller Board? Could i controll it via can?

Hi,
a little question... How high i could go with the input DC Voltage? I use 60Ah 300Amax Cells, and i would get the most power out of it

Hi,

Is it possible to program the controller in such a way that one can charge 230V / 16A single-phase or 3x400V / 16A multi-phase without changing programming / wiring in between? Does the controller start when all three modules are switched to "on", but only one is energized?

Hi,

great, this works. So i tried to send the "boostcalc" (Value = 2200). The CAN Massage says 98 08 00 00 00 00 00 00 '........'
The "dir" equals "00 00 00 00 00 00 00 00". Is there a Table that show what a bit means in such situation?

But ive could controll the "pot" for Regen over CAN ...

Hello,
@ Dima: I can receive the CAN message, but interpret what I should say the number (see screenshot) I can not. For me, I see no connection with the value that should actually be transferred (V.4.7.0).

What would help me:
An exact example like me put the value "Version" on the CAN and how I ...

Hi,
i buy a "CanUSB" Dongle and now i see CAN-Signals :)
I try to send the "Version" Value "4.17.R" to the CAN. I find the CAN-Package (001), but in there is only this
CAN.png

I Write in the WebInterface at "Version" row :
-CanID : 001
-Position : 1
-Bits : 16
-Gain : 1
-Map to Can TX

Sorry, im ...

Hi,
yea can speed at 250k, Bus terminatet with 120ohm.
I would try another can sniffer next week, the actual one is not the Best (25€ cam Bus analyzer)

Hi,
I tried. But i couldnt get any Signal from the can sniffer. With the can in my smart roadster, i could read out the Massages.

Im new with can Systems and the Controllerboard /Webinterface.

And the "Position"? They couldnt mean bit 2, when Thema Information is one Byte long.

Hi,
But a "2" in Theorie length and Position field means what? Two Byte, Two bit?
thats the thing that was unclear.

Hi,
i have my problems with "Position" and "Bits". What exactly i should write in the boxes?
Bits = 8 , Position = ?

Hello,

I can not cope with the little information of the wiki.
How can I send CAN signals? The table in the web interface, unfortunately, I do not quite understand. Is there a description of what is meant by "Plot" "l" "r" "Map to CAN" and so on? How do I get the engine temperature for example on ...

Hi,
Patrick Hagemann here
About two months ago I bought a board from you (built up and tested).
The values for maximum current etc. are set to 5000A, so I was careful if the other parameters are correct.

Thx for the help.

Hi,
i have a SDU and installed a Controller von Damien.
Sadly the documentation is not realy "Noob-Friendly". Is there a Parameter-Setup for the "first Start" ? I dont want to kill the Inverter on first try.

Thx