Sold as the entire lot. Thanks for looking..

Additional pics

Hello all, unfortunately I've not got the time to proceed with my projects. Therefore I'm basically putting a Lexus GS 450H parts (kit) up for sale. I'd prefer someone takes the entire lot versus parting it out, which I might need to do. Everything works, or did 6 months ago, have not touched it ...

Anyone still in the market for shunts? I have 2

Are you still looking for Lexus bits?

I have a used but unboxed GS450H Gearbox Oil Pump 56010-HRA030 For Sale.. If you're interested please PM me.

What are the correct connectors for the oil pump / oil pump controller which are needed, i believe i have the first one on the wiki page (the 2 way) but the second one (7-way) doesnt have a part number listed

edit: found it: 90980-12483 but does anyone have a uk or Europe based source of them ...

I’ll not had any issues bench testing when supplying the throttle pedal ground via VCU versus another ground. I’ll assume there is a specific reason for the VCU supplying ground versus it being feed elsewhere

Awe man. That's tidy.
What type of ties are you using there for the HV cables under the body? Way-hey better than my 'cable ties a go-go' attempt :?


Thanks, I'm extremely jealous of your complete build!! Hilltop cable management, 6mm hole, some sealant and these babies..

https://www.hilltop ...

Its been a while, so time to update the group. What's changed?
High Voltage cables have been installed
CANBus capture and hacking in progress
Nissan Leaf battery pack delivered, not dismantled as I want some stats from the BMS first if possible
GS450H gearbox, ATF fluid changed, fully wired up and ...

Anyone have any recommendations for water based cabin heaters besides the Nissan Leaf version? I don't want to rip out my dashboard to install a matrix unit if I don't have to. Looking for something already hacked, tested, and possibly on the inexpensive side.

Couple of additional pics

Update: 10/7/2020

Car has returned from fabricators and I'm well impressed. Shout out to Zack @Anarchy_Kustomz for the professional looking work!! The gearbox isn't going anywhere.. Dropping the gearbox easily was one of the main requirement. Zach and I are working on costings if anyone wants a ...

Any ideas on how the centre of this comes out? I recall Damian’s video shows him wielding it to a bit is square tube.


It may be too late now. But do you happen to have the part number for that piece? My gearbox didn't come with it.


I cut it out of this.
61829558-2377-42F6-8B8B ...

Any ideas on how the centre of this comes out? I recall Damian’s video shows him wielding it to a bit is square tube.

Thanks Matt, I was able to tweak the following in V7 of the code define drive versus neutral.

//set initial conditions/////////////////
T15Status=false;
dash_status=false;
can_status=false;
RPM=750;
Gcount=0x0d;
gear=NEUTRAL;
shiftPos=0xb4; //select neutral ...

The gearbox fits like a glove and the car is now with a fabricator to create new mounting points, gearbox face incorporating the spline to lock the two motors, bracing underneath, and interface the prop shaft between the Lexus and Merc differential. I know my limitations...

IMG_3687 2.jpg
IMG ...

Welcome to the electrification of a Mercedes Benz SLK. Goal is to convert a pre February 2001 as there are currently massive tax saving implications in London for electrically converted cars up to 28/2/2001; no road tax £285per year, £15 congestion charge per day , £11.50 Ultra Low emissions zone ...

Robbertjanzen wrote: ↑Wed May 13, 2020 6:37 pm I have updated the drawing after some remarks and updates found in the software.

Hope this helps

Amazing, helps to see the whole picture. Thanks again.

Filip wrote: ↑Sat May 09, 2020 5:36 pm Ok, here's the list!

36638-0002 CMC header connector 48pin 1pc
64320-1311 CMC receptacle 48pin 1pc
64320-1301 CMC wire cap 1pc
64323-1039 CP terminal 4pcs
64323-1029 CP terminal 32pcs
64325-1010 CMC plug 8pcs
64325-1023 CMC plug 4pcs

Brilliant.... Thank you

This is my version of inverter connector, based on Molex parts.


First I tore the original connector apart
IMG_2118.JPG

Then I soldered the wires to the new connector.

After that it was time to try to fit the new connector to the inverter, I used the old connector and cut it flush.
IMG_2119.JPG ...

The thread on the GS450h gearbox connections has all the info you need. Auto-click in the UK has required connectors. You can also buy the other connector from them too.

https://openinverter.org/forum/viewtopic.php?f=14&t=271&start=10


Above you state Auto-click has all the necessary ...

It's glued/bonded in - I had to smash mine out. I think I used a screwdriver and then a craft knife to clean up the rest. Be careful not to cut yourself or scratch the aluminium, it's a mating face for my cover!

DC bus cover pictured in my last post is done. I just want to add o-ring grooves ...