Hi Forum.

All now sold, thanks to everyone who looked at the ad.

Peter

It is right hand drive.

Hi Forum

Could be the last time I offer the package or was I being hopeful ??

Eventually someone will see what a bargain I am offering

Please see my earlier main post for details and pics dated 09 JUNE 2024.

Original advert ... viewtopic.php?p=71619#p71619

Thanks. Peter

Hi Forum

Could be the last time I offer the package ??

Eventually someone will see what a bargain I am offering

Please see my earlier main post for details and pics dated 09 JUNE 2024.

Original advert ... viewtopic.php?p=71619#p71619

Thanks. Peter

Thanks jrbe. Makes life a little easier for someone

Hi Forum

Yes... its been reduced again !

Eventually someone will see what a bargain I am offering

Please see my earlier main post for details and pics dated 09 JUNE 2024.

Thanks. Peter

Hi Forum.

Please see earlier classified listing for details as its now reduced to £1700, and will be reduced further !

Hi Forum. Due to ill health and not getting any younger I have decided its time to stop crawling under cars. I am selling my ex- 1.4 litre Alfa Romeo Mito Sprint 2011 which is 85% complete as an EV. Fitted with Tesla Model X (P100D) SDU using bespoke design stainless carrier. Has bespoke drive shaft...

The voltage could go higher when in regen.

Hi Forum. I am not able to finish my latest project so looking to sell as is or will break as a last resort. Alfa Romeo Mito 2011, was 1.4 litre manual. Note the 'was'. Vehicle is in good order too, not a rusty wreck ! All ICE stuff, noisey smelly bits all removed. Now fitted with Tesla SDU Model X ...

Thanks royhen99. That answers my question. Have a good day. Peter

Hi Forum. Has anyone got a picture of the battery in the 2018 LAND ROVER RANGE ROVER SPORT EV/Hybrid High Voltage Battery 48V pack please? There are a few for sale on Ebay but I cant find any pics of the actual battery just the whole battery/dc-dc etc. Info says its 48v and 15kWh which is fine for m...

Thanks to all who replied. Looking at the options and prices.....

Hi Forum. I am looking for a 120v - 134.4v lithium battery charger with 10 -20A or more charging capability. Has anyone seen such an animal ??
Thanks. Peter

Hi nkiernan.
35mm cable, 3.5M length, joint at 2M from plug.
Plug number, 9-2141147-1
ZSB -2141154

Cable and plug pre-assembled 2M length2177201-8 TE HV

Based North West Lancashire, where are you ?

Hi Jacobsmess. Thank you for contacting me.
What are you interested in please?

Hi Forum. I have run out of time to finish my latest conversion so looking to sell as parts to forum members. Tesla Model X P100D 2018 SDU from my last running conversion (Smart 450). Complete with bespoke oil/coolant heat exchanger with 12v external elec pump and filter. (Motor was run in reverse i...

You should see the voltage change across the resistor at start of precharge and at the end as the capacitors charge up. Should be a high voltage across it at the initial start of precharge which reasonably quickly drops to a few volts after a second or two. As another test put a load across the inve...

Also measure voltage across 50 ohm resistor during the precharge.

Ok Lood. 50 ohm is fine. I am hoping you can monitor the udc voltage before the precharge drops out. Good luck.

Hi Lood. Try lowering udcsw to say 160v and see if the precharge drops out again at 5 secs. I would also be monitoring the dc readout on the parameters to see if the dc voltage rises during the 5 secs. Whats your precharge resistance value? Need that info first Pete

Hi Forum. Does anyone have a working Arduino programme for talking to SAE J1850 PWM bus please? Tons of stuff on the web for VPW but not PWM :-( Any help appreciated as I am trying to retain my dashboard and use the original dials for EV purpose. RPM as Amps, Fuel as SOC and Temp as SDU temp. So far...

Thanks Johannes.
Looks so easy when I talented man as yourself is online
All the best. Peter

Hi Forum. Looking for some help please... I am using an Arduino Uno and a SEED CAN adaptor to hack my vehicle. I can read the bus so I know all is well hardware wise. I now want to send a CAN message but I see the Arduino IDE sketch starts the message ID as 0x?? BUT, the address I wish to talk to on...