I've a rebuild pack coming from aiways (probably U5 model) dismantled pack (180Ah 4s1p catl modules) . I do not have any info about size of maxxus model. Maxxus has also LFP version AFAIK.
If you have info about these pack, please share or add that info in a wiki.

check all reaf can bridge related repos here https://github.com/dalathegreat there you have amny pieces where to do Sail Mode (I've it installed in aze0). I do not suggest to increase power other if you have a custom battery pack that allow enough discharge.
I do not know any code implementing one ...

You can only purchase a pre-programmed LBC module of all Leaf(Gen1-Gen3), with a pre-agreed battery power, the price is the average price of LBC + $150.



Hi, I'm interested in this firmware, how to proceed? I've a 63kWh catl setup and different BMS . the idea is to run it in ZE1 model.

let me ...

FYI current sensor pinout for 62kWh nissan leaf BMS is different from that used for 40kWh.
I measured the continuity directly from current sensor harness to the bms harness. Note. in the middle there is another harness entering in the junction box where the current sensor is located.
the result ...

PSA groups 75 kwh battery packs with CATL modules for sale. Delivery to all of EU. Battery packs are NEW and not used. Around 30 full packs available. Please PM if interested. Price negotiable.


any idea of what module are used XsYp configuration and size of the components inside? do you have ...

FYI because online services can close, I would suggest to download 3d models ans save here as attachements leaving clear the source and license of the original files

you can find all info here
https://mynissanleaf.com/threads/revers ... bms.36627/

ekohn04 wrote: ↑Fri Nov 22, 2024 8:32 pm Hi everyone,
After some very frustrating BMS issues, I discovered that the terminal of one of my cells had been pulled off of the cell stack.

what was the issue shown by the BMS?

Here you have

I remember 33 and 34, btw I'll check for it in the documentation if any

Hi, always available for sale Nissan Leaf 40 & 62 kwh battery packs. Prices vary depending on Soh and delivery location but can start at ~£3500. Delivery possible within UK and most of EU. Please PM for details. 😊


can you give me what do you have available, what soh and hx and km and at what ...

Hi (sorry for cross posting)

to repair a leaf 62kWh battery, I need for one of the internal modules, the central one that is a 4s3p of 2.5kWh.
Code is of the module is: 95B9-4NP9C

Possible location in EU.

Let me know,

tnx, Ginetto

Hi

to repair a leaf 62kWh battery, I need for one of the internal modules, the central one that is a 4s3p of 2.5kWh.
Code is of the module is: 95B9-4NP9C

Possible location in EU.

Let me know,

tnx, Ginetto

johu wrote: ↑Mon Oct 23, 2023 8:04 am Attachment limit raised, try uploading now

here attached you have the ZE1 Network Diagram document where available all harnesses and network

johu wrote: ↑Sun Oct 22, 2023 5:20 pm just saw this. How large is the file?

20.5MB

Huskte wrote: ↑Sat Oct 07, 2023 12:42 am I think i understand what's going on lol, Is it using ac? or just pulling air through the battery box?

AC because in this way can also remove or reduce a lot humidity and the air injected in the battery

Planning on using a 40kwh pack from a 2018 (or newer) leaf, do you guys think it's worth cooling the battery box?

Eg putting a fan on one end to blow cooler air though the box for pre fast charging? or cooling down when stuck in traffic in the summer?


Here a "risky" solution using AC air ...

Adamzki wrote: ↑Tue Jun 13, 2023 1:33 pm Hi ginetto. Please could you PM me the diagram too.

is there a way to store this pdf in the openinverter space?
I can't attach here due to size

Just received my used indra v2g device that I suppose not able to use in v2g because outside UK. Do you have any detailed teck info about the PRE v2g500 inverter model? I can find only this short document: https://www.chademo.com/wp2016/wp-conte ... asheet.pdf

I found harness and wiring diagram fo ZE1

PM with your email to sent it or better allow admin to attach a larger file (20MB)


Hello, I have a ZE1 Leaf stack, with complete wiring (fortunately).
The connector at the end of the signal wires looks like this:
image.png

Can you please help me ...

Bigpie wrote: ↑Thu Mar 16, 2023 6:47 pm Does this mean you was able to code a fresh LIM without the BDC simulator, BMW i3 BDC and key?
Could you provide instructions for the wiki on this method?

Look into Damien Macquire youtube channel... there is a video about this (and reference to github repos)

Hi guys, just wanted to ask if anybody used a Duosida CCS socket with a LIM and got it working? I read through the thread and a lock seems to be a must. By lock is it meant the Type2 socket lock on the top as in the photo? If so it is rather high profile has anybody seen any smaller versions of ...

christoph wrote: ↑Wed Nov 02, 2022 9:28 am I't's a Legacy Nissan Leaf 2016 with battery upgraded to 40kWh. I'm currently working on simulating a Chademo charge. There will soon be a blog post on EVCreate (Lars') blog describing the project.

tnx christoph

It works! On ABB chargers at least. Tested on two different ones.

On Efacec it stops after some seconds of actual charging. But investigating... I made a log...

Thanks everyone involved!


That's my next step after upgraded my 2016 leaf to 62kWh battery with Dala's firmware and can bridge.
I ...