Tesla Model S/X GEN2 Charger - Revision history

Asavage: /* Replacement board connectors */ Punctuation.

2026-02-27T17:12:52Z

Replacement board connectors: Punctuation.

← Older revision		Revision as of 17:12, 27 February 2026
Line 116:		Line 116:

	=== Replacement board connectors ===		=== Replacement board connectors ===
	If you can desolder 24 pin SMD connector ~~off of~~ the OEM control board otherwise to order 24 pin connector from Mouser P/N is:		If you can, desolder the 24 pin SMD connector from the OEM control board; otherwise, order the 24 pin connector from Mouser, whose P/N is:

	* [https://www.mouser.com/ProductDetail/JST-Automotive/SM24B-CPTK-1A-TBL?qs=wBn5QRdTcLhQ%2FCp3E8a%2FyA%3D%3D SM24B-CPTK-1A-TB(L)]		* [https://www.mouser.com/ProductDetail/JST-Automotive/SM24B-CPTK-1A-TBL?qs=wBn5QRdTcLhQ%2FCp3E8a%2FyA%3D%3D SM24B-CPTK-1A-TB(L)]

	The 30 pin connector is very difficult to desolder and resolder. Replacement P/Ns are:		The 30 pin connector is very difficult to desolder and resolder. Replacement P/Ns are:

	* [https://www.mouser.com/ProductDetail/Samtec/IPS1-115-01-S-D-PL?qs=PB6%2FjmICvI17nbB5SDGUsw%3D%3D IPS1-115-01-S-D-PL], SAMTEC - IPS1-115-01-S-D-PL - SOCKET, 2.54MM, ~~2X15WAY~~		* [https://www.mouser.com/ProductDetail/Samtec/IPS1-115-01-S-D-PL?qs=PB6%2FjmICvI17nbB5SDGUsw%3D%3D IPS1-115-01-S-D-PL], SAMTEC - IPS1-115-01-S-D-PL - SOCKET, 2.54MM, 2x15WAY
	** NOTE: One of the pins is missing from this connector variant, but according to [https://openinverter.org/forum/viewtopic.php?p=27697&hilit=charger+pin+missing#p27697 this forum post], it's ok as long as you solder it in the correct orientation.		** NOTE: One of the pins is missing from this connector variant, but according to [https://openinverter.org/forum/viewtopic.php?p=27697&hilit=charger+pin+missing#p27697 this forum post], it's OK as long as you solder it in the correct orientation.
	* [https://www.mouser.com/ProductDetail/Samtec/IPS1-115-01-L-D?qs=PB6%2FjmICvI3sN4zSP4IXGw%3D%3D IPS1-115-01-L-D], SAMTEC		* [https://www.mouser.com/ProductDetail/Samtec/IPS1-115-01-L-D?qs=PB6%2FjmICvI3sN4zSP4IXGw%3D%3D IPS1-115-01-L-D], SAMTEC
	** Has all 30 pins.		** Has all 30 pins.

Arber333 at 17:42, 30 October 2025

2025-10-30T17:42:08Z

← Older revision		Revision as of 17:42, 30 October 2025
Line 8:		Line 8:

	The charger is made up of three 3.3 kw modules, each sitting on a liquid cooling plate. This assembly enables both single and multi phase AC charging.		The charger is made up of three 3.3 kw modules, each sitting on a liquid cooling plate. This assembly enables both single and multi phase AC charging.

			Tesla gen2 charger weighs 16kg!!! Surprisingly low for such a bulky item

	==Important Considerations==		==Important Considerations==

Tom91: Categories

2024-12-20T16:30:39Z

Nubster: /* Replacement board connectors */ added link

2024-11-28T21:31:42Z

Replacement board connectors: added link

← Older revision		Revision as of 21:31, 28 November 2024
Line 116:		Line 116:
	If you can desolder 24 pin SMD connector off of the OEM control board otherwise to order 24 pin connector from Mouser P/N is:		If you can desolder 24 pin SMD connector off of the OEM control board otherwise to order 24 pin connector from Mouser P/N is:

	* SM24B-CPTK-1A-TB(L)		* [https://www.mouser.com/ProductDetail/JST-Automotive/SM24B-CPTK-1A-TBL?qs=wBn5QRdTcLhQ%2FCp3E8a%2FyA%3D%3D SM24B-CPTK-1A-TB(L)]

	The 30 pin connector is very difficult to desolder and resolder. Replacement P/Ns are:		The 30 pin connector is very difficult to desolder and resolder. Replacement P/Ns are:

Nubster: /* Replacement board connectors */

2024-11-28T21:29:06Z

Replacement board connectors

← Older revision		Revision as of 21:29, 28 November 2024
Line 118:		Line 118:
	* SM24B-CPTK-1A-TB(L)		* SM24B-CPTK-1A-TB(L)

	The 30 pin connector is very difficult to desolder and resolder. Replacement P/~~N is~~:		The 30 pin connector is very difficult to desolder and resolder. Replacement P/Ns are:

	* IPS1-115-01-S-D-PL, SAMTEC - IPS1-115-01-S-D-PL - SOCKET, 2.54MM, 2X15WAY		* [https://www.mouser.com/ProductDetail/Samtec/IPS1-115-01-S-D-PL?qs=PB6%2FjmICvI17nbB5SDGUsw%3D%3D IPS1-115-01-S-D-PL], SAMTEC - IPS1-115-01-S-D-PL - SOCKET, 2.54MM, 2X15WAY
			** NOTE: One of the pins is missing from this connector variant, but according to [https://openinverter.org/forum/viewtopic.php?p=27697&hilit=charger+pin+missing#p27697 this forum post], it's ok as long as you solder it in the correct orientation.
			* [https://www.mouser.com/ProductDetail/Samtec/IPS1-115-01-L-D?qs=PB6%2FjmICvI3sN4zSP4IXGw%3D%3D IPS1-115-01-L-D], SAMTEC
			** Has all 30 pins.

	===Programming===		===Programming===

Nubster: /* Missing IC4 Chip Explanation */

2024-10-29T18:21:17Z

Missing IC4 Chip Explanation

← Older revision		Revision as of 18:21, 29 October 2024
Line 283:		Line 283:

	''Note: Its recommend that you change it. Nobody wants to drive and have some joker with a phone finding this information and accessing your charger.''		''Note: Its recommend that you change it. Nobody wants to drive and have some joker with a phone finding this information and accessing your charger.''

			'''Missing IC4 Chip'''

			According to [https://openinverter.org/forum/viewtopic.php?p=43750&hilit=ic4#p43750 this forum post], IC4 used to be populated with a USB to serial FTDI chip. However, on the latest boards, all settings are configured via wifi so it is no longer needed.
			[[File:Gen2ChargerBoard.jpg\|alt=Image of Tesla Gen2 charger board with missing IC4 chip\|thumb\|Tesla Gen2 charger board with missing IC4 chip]]

	====Registration====		====Registration====

Tom91: /* Parameters */

2024-07-11T18:59:51Z

Parameters

@@ Line 288: / Line 288: @@
 If you bought a fully assembled V5aB3 board from the EVBMW webshop you can skip this step.
-We will go over all of them.
+=== Latest Software for V5 boards and later ===
+[[Tesla Model S/Tesla Gen23 V5 Software]]
 ==Additional Resources==

Asavage: /* Functionality of external CAN bus */ Typo fix of "Motorola".

2024-06-25T22:11:40Z

Functionality of external CAN bus: Typo fix of "Motorola".

← Older revision		Revision as of 22:11, 25 June 2024
Line 261:		Line 261:
	\|		\|
	\|}		\|}
	LR: Personally I think the data for DC voltage limit is incorrect. The above states ~~Motorla~~ but only when I set all signals (so not only DC voltage limit as also the start bit count (sometimes) varies) to Intel it works for me.[[File:Parameter view of commercial firmware.png\|thumb\|Parameter view of commercial firmware]]		LR: Personally I think the data for DC voltage limit is incorrect. The above states Motorola but only when I set all signals (so not only DC voltage limit as also the start bit count (sometimes) varies) to Intel it works for me.[[File:Parameter view of commercial firmware.png\|thumb\|Parameter view of commercial firmware]]

	===openinverter style charger firmware===		===openinverter style charger firmware===

Larsrengersen: /* Supported Tesla Part Numbers (TPN) */

2024-06-25T10:25:46Z

Supported Tesla Part Numbers (TPN)

← Older revision		Revision as of 10:25, 25 June 2024
Line 26:		Line 26:
	TPNs tested and known good:		TPNs tested and known good:

	*1014963-00-E/F/J/K/L		*1014963-00-C/E/F/J/K/L
			**1014963-00-C <ref>https://openinverter.org/forum/viewtopic.php?p=34710#p34710 and also by Lars on June 25th 2024</ref>
	**1014963-00-G is likely also good, just wasn't mentioned by name in the referenced thread		**1014963-00-G is likely also good, just wasn't mentioned by name in the referenced thread

Larsrengersen: Added timedly description and suggestion for CAN control indianness

2024-06-25T09:54:59Z

Added timedly description and suggestion for CAN control indianness

← Older revision		Revision as of 09:54, 25 June 2024
Line 260:		Line 260:
	\|		\|
	\|}		\|}
	[[File:Parameter view of commercial firmware.png\|thumb\|Parameter view of commercial firmware]]		LR: Personally I think the data for DC voltage limit is incorrect. The above states Motorla but only when I set all signals (so not only DC voltage limit as also the start bit count (sometimes) varies) to Intel it works for me.[[File:Parameter view of commercial firmware.png\|thumb\|Parameter view of commercial firmware]]

	===openinverter style charger firmware===		===openinverter style charger firmware===
Line 320:		Line 320:

	Another charge end condition. Charge only for the specified time in minutes.		Another charge end condition. Charge only for the specified time in minutes.

			'''timedly'''

			The default value is -1 but this results in the charging waiting forever. You need to set this to 0 (or more) for the OBC to work.

	'''inputype'''		'''inputype'''

← Older revision		Revision as of 16:30, 20 December 2024
Line 332:		Line 332:

	==Notes==		==Notes==
	~~[[Category:OEM]]~~
	[[Category:Tesla]]		[[Category:Tesla]]
	[[Category:Charger]]		[[Category:Charger]]

	<references />		<references />