Updated terms

Introduction and miscellaneous that we haven't created categories for, yet
Post Reply
User avatar
johu
Site Admin
Posts: 6754
Joined: Thu Nov 08, 2018 10:52 pm
Location: Kassel/Germany
Has thanked: 382 times
Been thanked: 1575 times
Contact:

Updated terms

Post by johu »

I have added the following paragraph to the terms (always available here ucp.php?mode=terms) and shown to every user before registration:

The content of this forum serves educational purposes only. Working with power electronics and grid voltages requires profound knowledge to prevent accidents. Therefor neither openinverter.org nor its founder Johannes Hübner can be held responsible for any damage, injury or death caused by repeating the experiments presented here.

If you do not agree, delete your account
Support R/D and forum on Patreon: https://patreon.com/openinverter - Subscribe on odysee: https://odysee.com/@openinverter:9
arber333
Posts: 3572
Joined: Mon Dec 24, 2018 1:37 pm
Location: Slovenia
Has thanked: 134 times
Been thanked: 339 times
Contact:

Re: Updated terms

Post by arber333 »

I agreed with it way back from 2012! 8-)
User avatar
johu
Site Admin
Posts: 6754
Joined: Thu Nov 08, 2018 10:52 pm
Location: Kassel/Germany
Has thanked: 382 times
Been thanked: 1575 times
Contact:

Re: Updated terms

Post by johu »

Ok, so you can stay :)
Support R/D and forum on Patreon: https://patreon.com/openinverter - Subscribe on odysee: https://odysee.com/@openinverter:9
User avatar
tom91
Posts: 2420
Joined: Fri Mar 01, 2019 9:15 pm
Location: Bristol
Has thanked: 209 times
Been thanked: 577 times

Re: Updated terms

Post by tom91 »

johu wrote: Wed Jun 03, 2020 8:45 am The content of this forum serves educational purposes only. Working with power electronics and grid voltages requires profound knowledge to prevent accidents. Therefor neither openinverter.org nor its founder Johannes Hübner can be held responsible for any damage, injury or death caused by repeating the experiments presented here.
How about adding in nor forum users after Hübner? to make it clear that people should take responsibility when using the information provided by anyone via the forum.
Creator of SimpBMS
Founder Volt Influx https://www.voltinflux.com/
Webstore: https://citini.com/
User avatar
Kevin Sharpe
Posts: 1339
Joined: Fri Dec 14, 2018 9:24 pm
Location: Ireland and US
Been thanked: 8 times

Re: Updated terms

Post by Kevin Sharpe »

tom91 wrote: Wed Jun 03, 2020 10:07 am make it clear that people should take responsibility when using the information provided by anyone via the forum.
This is an important point.
This is a personal post and I disclaim all responsibility for any loss or damage which any person may suffer from reliance on the information and material in this post or any opinion, conclusion or recommendation in the information and material.
User avatar
johu
Site Admin
Posts: 6754
Joined: Thu Nov 08, 2018 10:52 pm
Location: Kassel/Germany
Has thanked: 382 times
Been thanked: 1575 times
Contact:

Re: Updated terms

Post by johu »

Yes will do
Support R/D and forum on Patreon: https://patreon.com/openinverter - Subscribe on odysee: https://odysee.com/@openinverter:9
User avatar
Kevin Sharpe
Posts: 1339
Joined: Fri Dec 14, 2018 9:24 pm
Location: Ireland and US
Been thanked: 8 times

Re: Updated terms

Post by Kevin Sharpe »

johu wrote: Thu Jun 04, 2020 5:56 pmYes will do
Any progress with a liability disclaimer for forum members?
Screenshot 2020-07-14 at 19.32.20.png
This is a personal post and I disclaim all responsibility for any loss or damage which any person may suffer from reliance on the information and material in this post or any opinion, conclusion or recommendation in the information and material.
User avatar
johu
Site Admin
Posts: 6754
Joined: Thu Nov 08, 2018 10:52 pm
Location: Kassel/Germany
Has thanked: 382 times
Been thanked: 1575 times
Contact:

Re: Updated terms

Post by johu »

Of course - weeks ago...


Well I just added it ;)
Support R/D and forum on Patreon: https://patreon.com/openinverter - Subscribe on odysee: https://odysee.com/@openinverter:9
Post Reply